Quantcast
Channel: ASRock Forums
Viewing all 19545 articles
Browse latest View live
↧

Intel Motherboards : Cannot install Windows on M.2 ssd

June 26, 2020, 2:21 pm
$
0
0
Author: fairycakes
Subject: Cannot install Windows on M.2 ssd
Posted: 26 Jun 2020 at 9:21pm

I've tried diskpart to do everything I can think of. Anything in particular you can suggest? And sorry could you explain "run from the prompt"? Thanks
↧
Search

Intel Motherboards : Cannot install Windows on M.2 ssd

June 26, 2020, 3:00 pm
$
0
0
Author: fairycakes
Subject: Cannot install Windows on M.2 ssd
Posted: 26 Jun 2020 at 10:00pm

In legacy mode if I delete the partition and try again, I get "Windows cannot be installed to this disk. This computer's hardware may not support booting to this disk. Ensure that the disk's controller is enabled in the computer's BIOS menu."

Could it be a bios setting I need to change?
↧
↧

Intel Motherboards : H370M no boot

June 28, 2020, 9:04 am
$
0
0
Author: Do_n
Subject: H370M no boot
Posted: 28 Jun 2020 at 4:04pm

Hi
I get only 4 beeps, always and no video signal
Cmos was reset
Fans are running
Video is vga, more than adapter used and more than one monitor too
Psu is cx450m from corsair and psu tester says me all ok

Edited by ASRock_TSD - 7 minutes ago at 10:46am
↧

Intel Motherboards : Issues with E3C224D4I-14S (No POST?)

June 28, 2020, 2:50 pm
$
0
0
Author: intelligence
Subject: Issues with E3C224D4I-14S (No POST?)
Posted: 28 Jun 2020 at 9:50pm

I've been using this build for a couple of years now and for most part it's been working great, however now I can't seem to boot the system anymore. Friday night I realized that the box wasn't responding, the day after I fired up my IE10 VM to investigate the state of the box. IPMI was up and running, but when trying "Console Redirection" no image/video feed was shown.

Upon rebooting I was able to get into BIOS while hammering the DEL button and everything seemed fine. Trying to boot up my OS (FreeNAS) I had some issues as it seemed like the box kept dying during the OS boot. I figured that the USB with the OS on it was faulty so I switched it out, but it kept sporadically rebooting. At one point I was able to get the OS up and running, but it's only worked that one time out of perhaps 30 tries now.

I don't have a monitor with VGA making this hard to troubleshoot what's going on, but it seems the box is not POSTing at all anymore. Hammering DEL does nothing. Usually when I do that it beeps and lets me know I'm in BIOS settings, that doesn't happen anymore. Console Redirection gives me a blank screen.

I've tried removing all RAM and tried inserting them one by one in A1 slot, no dice. BMC led is blinking. I can access IPMI just fine. CPU fan spins up, drives spin up.

Eventlog in IPMI:
https://i.imgur.com/waQ7yUz.png

Specs:
E3C224D4I-14S (firmware: 0.18.00)
Intel Xeon E3-1241V3
4 x Kingston ValueRAM Server Premier 8GB 1600MHz DDR3L DIMM 240-pin

Any ideas what I can do now to try and find out what's wrong?
↧

Intel Motherboards : Monitor no signal new omotherboard

June 28, 2020, 3:08 pm
$
0
0
Author: lucas.dutra
Subject: Monitor no signal new omotherboard
Posted: 28 Jun 2020 at 10:08pm

Hello! I just installed an asrock fatal1ty m360 performance motherboard. However, the monitor never receives a signal. I have already tested the following actions:

1. I removed everything not essential;
2. Reset the bios by the battery and the jumper;
3. I changed the Slot Ram
4. I connected the monitor via hdmi and vga

Core i5 9400F 9th gen
Memory: BLS8G4D26BFSCK.8FD


I thought about testing with an off board video card, but this would be to work around the problem and not solve it.

Would anyone have any more ideas?
↧
↧

Intel Motherboards : Boot Failure Guard kicking in after unpluggin PSU

June 28, 2020, 3:28 pm
$
0
0
Author: dexter47
Subject: Boot Failure Guard kicking in after unpluggin PSU
Posted: 28 Jun 2020 at 10:28pm

Problem solved. I have changed the CMOS battery.

Is there no way to edit a post?
↧

Intel Motherboards : Z390 Pro4 with 4-pin power connector

June 28, 2020, 11:14 pm
$
0
0
Author: Guipoggi
Subject: Z390 Pro4 with 4-pin power connector
Posted: 29 Jun 2020 at 6:14am

I have finishing assembling my PC (Z390 Pro4 with Intel i5 9600k) and, when I was turn it on, the lights go on but nothing else works... And the PC lights sometime go off and then on again... seeming like a lack of power.

I have installed a 500w PSU (more than enough for my setup) and it has two power connectors for the Motherboard: a 24 pin and a 4 pin. The manual says I can use a 4 pin connector... I have plugged both connectors and the problem persists. Please help.
↧

Intel Motherboards : asrock app shop

June 29, 2020, 12:05 am
$
0
0
Author: johnnyc256
Subject: asrock app shop
Posted: 29 Jun 2020 at 7:05am

Asrock z170 k6 gaming motherboard. Sometimes it starts up then it disappears from the taskbar. If you don't run the program on startup, then the program doesn't open unless you start it two times.
↧
Search

Intel Motherboards : ASRock Z370 ITX Fatal1ty PCIE lanes M2 NVME drive

June 29, 2020, 3:27 am
$
0
0
Author: jonfitch
Subject: ASRock Z370 ITX Fatal1ty PCIE lanes M2 NVME drive
Posted: 29 Jun 2020 at 10:27am

I'm having trouble seeing how many PCIE lanes the Z370 ITX Fatal1ty has in total, is it 16 or 20? If I install a NVME M2 PCIE drive like the Adata SX8200 Pro or WD SN750, does that drop the graphics card down from 16x to 8x speeds?

Also second question, since the M2 NVME drive is on the back of the motherboard, is it better to have a heatsink on or off?

Thanks
↧
↧

Intel Motherboards : New Z390M ITX/AC terrible wifi performance

June 29, 2020, 3:35 am
$
0
0
Author: ASRock_TSD
Subject: New Z390M ITX/AC terrible wifi performance
Posted: 29 Jun 2020 at 10:35am

Dear Mattyfresh,

Thanks for posting!

The driver version will not always be the same when installed. Sometimes the driver version will show one version, once installed it will show different numbers in the system. It is normal.

Let's get into the WiFi question,
1. Please make sure to connect antennas to the system.
2. Has the WiFi been connected via a different router or network to see if it is the network/router related?
3. Also, on the page. 7 there is an M.2_WiFi1 bundle next to the LAN port, please try to remove the bundle and check if the WiFi cable is connected to the WiFi module properly.

With thanks,
ASRock TSD



Edited by ASRock_TSD - 15 minutes ago at 10:38am
↧

Intel Motherboards : H370M no boot

June 29, 2020, 3:42 am
$
0
0
Author: ASRock_TSD
Subject: H370M no boot
Posted: 29 Jun 2020 at 10:42am

Dear Do-n,

Thank you for posting!

Could you provide the name of the CPU that is being used?

With thanks,
ASRock TSD

Edited by ASRock_TSD - 7 minutes ago at 10:46am
↧

Intel Motherboards : Monitor no signal new omotherboard

June 29, 2020, 3:51 am
$
0
0
Author: ASRock_TSD
Subject: Monitor no signal new omotherboard
Posted: 29 Jun 2020 at 10:51am

Dear Lucas,

Thanks for posting.

The 9400F CPU does not have the integrated graphics supported.
Kindly install a graphics card to the PCIe slot.

With thanks,
ASRock TSD
↧

Intel Motherboards : Z390 Pro4 with 4-pin power connector

June 29, 2020, 3:58 am
$
0
0
Author: ASRock_TSD
Subject: Z390 Pro4 with 4-pin power connector
Posted: 29 Jun 2020 at 10:58am

Dear Guipoggi,

Thanks for posting your query to the ASRock forum.

Regarding your question,
1. Please remove the power connector and refer to the page.19 from the link below to clear the CMOS.
   https://download.asrock.com/Manual/Z390%20Pro4.pdf
2. Please try to reinstall the RAM to different slots.
3. Please try reinstalling the CPU. (Check if the CPU pins are in correct shapes)
4. If possible, please try with a different RAM.

With thanks,
ASRock TSD
↧
↧

Intel Motherboards : ASRock Z370 ITX Fatal1ty PCIE lanes M2 NVME drive

June 29, 2020, 4:02 am
$
0
0
Author: ASRock_TSD
Subject: ASRock Z370 ITX Fatal1ty PCIE lanes M2 NVME drive
Posted: 29 Jun 2020 at 11:02am

Dear Jonfitch,

Thanks for posting.

Installing an M.2 will not affect the PCIe slots so the PCIe slot will always provide x16.

If the chassis can fit the M.2 heat sink, please install the heat sink on the M.2 slot.

With thanks,
ASRock TSD
↧

Intel Motherboards : H370M no boot

June 29, 2020, 9:51 am
$
0
0
Author: Do_n
Subject: H370M no boot
Posted: 29 Jun 2020 at 4:51pm

https://www.amazon.it/gp/product/B07P871J57/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

https://www.amazon.it/gp/product/B07WD5VKVL/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

Thanks
Donato
↧
Search

Intel Motherboards : Monitor no signal new omotherboard

June 29, 2020, 2:20 pm
$
0
0
Author: lucas.dutra
Subject: Monitor no signal new omotherboard
Posted: 29 Jun 2020 at 9:20pm

Thank you so much for your answer.
I haven't done anything related to hardware in a while, I didn't even know there was a processor without a gpu. So much so that it didn't even cross my mind and I went to the forum to try to identify the problem.
Now I have to find a solution for this ;-)
Thank you again.
↧

Intel Motherboards : Asrock Z390 Extreme4 unstable work with 9900K

June 29, 2020, 5:13 pm
$
0
0
Author: devd
Subject: Asrock Z390 Extreme4 unstable work with 9900K
Posted: 30 Jun 2020 at 12:13am

Asrock Z390 Extreme4 unstable work with 9900K CPU.

I installed Ubuntu 20.04 LTS (5.4.0-39 kernel).
The system freezes or reboots periodically.

Hardware:
CPU: Intel(R) Core(TM) i9-9900K
Memory: 4x16 Kingston HyperX Fury DDR4 3200 ??? KHX3200C16D4/16GX
Power water cooling: less than 50 degrees on CPU.

BIOS updated to 4.30 (no changes)

Intel Hyper Threading disabled.
Intel Turbo Boost enabled.
MultiCore Enhancement enabled.
CPU C3,C6,C7,C10 States disabled.

Memory tests passed successfully.
↧
↧

Intel Motherboards : H370M no boot

June 29, 2020, 5:22 pm
$
0
0
Author: Xaltar
Subject: H370M no boot
Posted: 30 Jun 2020 at 12:22am

So you are using a discrete GPU yes? Intel CPUs ending in "F" do not have integrated
graphics.

Make sure your GPU and RAM are properly seated into their slots.
↧

Intel Motherboards : Z390 Extreme 4 doesnt post

June 29, 2020, 9:03 pm
$
0
0
Author: fraserhutch
Subject: Z390 Extreme 4 doesnt post
Posted: 30 Jun 2020 at 4:03am

Hi.

I just put together a build but it wont post. I know the ram is good, because I have another system built on a Z370 Pro4 that has been working great, and I swapped out the ram between the two systems. Both sets of RAM worked on the Z370 so I know they are good. so I know the RAM is fine.
All the fans are working. No beeps, just a steady pulse of the blue lights on the motherboard.

I know this board at one time worked fine because I installed it on the other system until I realized I needed a different PCI slot so I got the Z370 and used that. So the Z390 *should* work.

So, I read a bunch of email from this site and none of the proposed fixes seem to apply - I attached a 8-pin CPU cable to the ATX12V1 connector, a 24 pin cable to ATXPWR1. FWIW, I did not connect anything to the 4-pin ATX12V2 connector. Do I need to -I don't have another CPU cable.
S
When I supply power from the PSU the blue lights on the motherboard start to pulse maybe once per second.
When I press the power button on the IO panel all the fans (case fan, CPU heat sink fan, and GPU fans stat up. The only think I hear is the tiny amount of crinkling that IIRC is a hard drive starting up.
I get no output from my GPU. No beeps no sound, just the fans running and the steady pulse of blue lights.

I hear NO beeping at all. The IO panel connectors seem to work fine - I have IO panel lights and the power switch starts the CPI and GPU fans.

This is my build:
ASRock Z390 Extreme 4
Intel I9-9900KF (coffee lake) CPU - no onboard graphics.
Corsair Vengeance LPX DDR4 2x16GB (32GB) 3200 MHZ
Hyper 212 EVO heatsink/fan.
Gigabyte GEForce RTX 2060 Super Graphics card
Corsair RM850 power supply.
Fractal Designs Define R5 case.
Crucial MX500 SSD
Seagate Barracuda SATA Hard drive.

I really haven't seen any means of diagnosing the issue.

Thanks fr all suggestions/advice,

Fraser







↧

Intel Motherboards : M.2 Nvme Asrock Z97 Extreme 4

June 30, 2020, 1:54 am
$
0
0
Author: johnnyc256
Subject: M.2 Nvme Asrock Z97 Extreme 4
Posted: 30 Jun 2020 at 8:54am

Did you use disk management in windows to set up a bootable partition in your nvme drive? Windows will not see your drive until you set up a partition and format the drive, I set my nvme drive by cloning the drive from my previous boot drive using Acronis true image which came with my crucial p1 1gb nvme drive.
↧
Viewing all 19545 articles
Browse latest View live
Search
<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>